Canon, the Canon logo, and imagePROGRAF are trademarks or registered Ink used for maintenance purposes such as head cleaning is absorbed. (Replace. Complete The Survey. No, Thank You. Canon · Consumer Product Support imagePROGRAF Series Support – Download drivers, software, manuals. Products. imagePROGRAF iPF Drivers & Downloads; Manuals; NEED SERVICE? imagePROGRAF iPF Specifications · Drivers & Downloads · Manuals.

Author: Marisar Mazucage
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Marketing
Published (Last): 15 March 2008
Pages: 404
PDF File Size: 19.25 Mb
ePub File Size: 18.60 Mb
ISBN: 833-7-37523-523-9
Downloads: 89609
Price: Free* [*Free Regsitration Required]
Uploader: Mezil

Chapter 1 Operating noise Operating: It supports the following functions: Page Chapter 2 Cleaning operation timings are as follows. By executing this mode, – Backup data of the settings kpf9000 counter values stored in the maintenance cartridge relay PCB are moved to the new main controller PCB.


Nozzle Pitch 1, dpi x 2. Page Chapter 4 b Reinstalling ink tank units The left and right ink tank units are installed to different positions at waste ink tray [1].

Rear Chapter 1 1. Chapter 1 1 Lift the Basket Rod gently to release the lock, lower the stacker toward mankal front, and push it all the way back.

Canon iPF9000 Series. Service Manual. Parts Catalog

Chapter 3 8 Attach the basket rod at the front of the basket unit to the tips [1] of the basket arm L and R. Chapter 4 1 To remove the valve motor unit, remove the ink tank cover unit. C Reserved Address signal 1 N. When touching a linear scale and the carriage shaft, it might cause defective movement of the carriage and a defective print.

Therefore, be sure to note the following points when i;f9000 the roller. Chapter 1 Printable area Roll media Internal area, excluding a 5-mm top, bottom and left and right margins.

In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbolthe arrow indicates the direction of the electric signal. Adhesion Of Ink Chapter 1 1.

Page 95 Chapter 1 2. Prepare For Parts Replacement. Checking The Contents Chapter 3 3. When the printhead is secured to the carriage, the signal contact of the head relay PCB is pressed against that of the printhead to convey print signals.

See your browser’s documentation for specific instructions. F 3 Turn and remove the joints from the bottom cardboard seat, and then remove the stand support cardboard. Consumption Printer status Cleaning operation typ.

Canon iPF Series. Service Manual. Parts Catalog

Warranty replacement shall not extend the warranty period of the defective Product. This pH neutral polyester blend canvas mannual a bright white, matte finish surface. Page 67 Chapter 1 2. Pay careful attention to all individually packaged service part carriage unit, purge unit, ink tank unit, and other parts boxes marked “This side up” and xanon appropriately.

Chapter 3 7 Raise the ink tank lock lever and remove all ink tanks. Bring the power cord of the right media take-up unit to the back of the printer and pass the cord through the cord holders.

Further, the ink passage from the ink tanks is connected to the printhead via the ink tubes.

Choose Yes to cut the roll at the current position. Chapter 4 1 To remove right front cover [1], remove right circle cover Lright circle cover Sright side covers, upper right cover the operation panel.

Allowed tilting angle Lengthwise: Search Our Knowledge Base Please enter your question: To prevent foreign matter from entering the ink port, installed the unpacked ink tank in the printer immediately. The sole warranty, if any, with respect to such non-Canon brand item is given by the manufacturer or producer thereof.

The maximum printable length from Printer Driver is 50 feet.

Chapter 1 3 Store the left and right Basket Rods. Each tank is available in two capacities: Unpacking the Ink Tank Do not unpack the ink tank until you are ready to install it.

Manual front loading Cut media: Basic Operation Outline Chapter 2 2. Insert the protruding portion [1] of each leg cover in the groove [2] in the stand upper stay, and insert the protruding portions [3] of the leg cover in the grooves [4] in the stand lower stay.

Actual prices are determined by individual dealers and may vary. Installing The Basket Chapter 3 3.